Finally arm and gatling gun for Iron Man War Machine (WM) is ready after more than a month without any update. It because I was preparing for PERI exhibition on the latest Toys and Comic Fair 2012 in Jakarta, for almost two weeks I didn’t making any template and last week I had a system failure on my PC resulting to re-format my Hard drive, that was also delay this WM progress. As usual I release in two template version, colored with 4 pages and blank one with 5 pages. In 1/6 scale the parts are very small but still can be build. In the last minute before finishing the template I re-examine all pages and found out there were some glue tabs/ flaps that were too small and I have them removed, and some parts have to be simplified because of the size of them, that alone took hours to be repaired. You have top follow all instructions step by step in order, because there are key steps which crucial to be taken in attention.
By using 2 mm thick card board layer part 36 with it then attach part 37 also with 2 mm cardboard on top part 36. We need 4 of this part, 2 pairs left and right for both arms. If you can't find 2mm cardboard you can use 2 layer of 1mm then stack them up ro achieve 2 mm thick. Don't forget to attach part 17 in its place on top of part 1.
. Wrap around part 1 with part 2. Place part 36 with 37 combined in part 1, use the guide line to align the part so the part below the guide line will be inside part 1
There will be two version of hands, this is the first one the other one, the closed fist will be released on the next part. It can be interchangeable.
In this instructions you will find slightly different parts in shape compare to template, It is because I have to simplified all the tiny parts. The parts I am talking about are part : 26,27,28 and 75
Place the machine guns on the back arm
assembly first part 65,66 and part 69. Part 66 has to rotate-able freely. Glue part 69 with 66, don't glue with part 65. Place the joint mechanism inside part 65 from the top before you close part 65.
Assembly part 76 them attach and glue it with part 66 so part 76 will be rotate-able.
Reinforce part 68 by stuffing with rolls of paper then hardened it with super glue, or you can replace part 68 with any material with the same size, the stronger the better.
Reinforce part 67 and 70 by stuffing with rolls of paper then hardened it with super glue, or you can replace them with any material with the same size. the stronger the better.
Document license
You may freely distribute or give away these paper models to others without prior permission from the designer, you may modify with the credit to paper-replika.com. Feel free to add any of these paper models to your website or blog, with the link to paper-replika.com model pages. Do not use direct link. Uploading to mass file storage for public view is forbidden, including, but not limited to, rapidshare, mediafire and others which provide similar service. All images are copyrighted. Permission is granted ONLY for non-commercial personal use. They may not be duplicated in any form, including electronic, mechanical or printed, for sale. All rights are reserved and duplication by any means,including, but not limited to, methods of printing, electronic storage and disk copies, is prohibited without permission. If you wish to use this artwork and instructions for other than your own personal use, like for a club contest or school program,PLEASE contact paper-replika.com for written permission.
This work is licensed under a
Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.
No Warranty is provided whatsoever. This material is provided on an as-is basis with no support and no warranty. All real life objects belong to its respective owners and designers.
This pattern never been tested, some minor errors were found in several of previuos models, please be advise maybe you will find errors such as missing tabs or unnecessary tabs, despite the models never been tested, many have succeeded build all of them perfectly, just need little imagination and dedication to this hobby.
To download this file you DO NOT NEED to be registered as a member, Registration whatsoever needed to join paper-replika.com FORUM and to give comments on articles. Paper-replika.com NEVER share your identity or sale to third party, and it will be kept safe.
We use third-party advertising companies to serve ads when you visit our website. These companies may use information (not including your name, address, email address, or telephone number) about your visits to this and other websites in order to provide advertisements about goods and services of interest to you. If you would like more information about this practice and to know your choices about not having this information used by these companies, click here.
PASSWORD : paper-replika.com (case sensitive)
Open PDF file with Adobe Acrobat Reader, PDO with Pepakura Viewer.
The assembly instruction is not include with the file that you are about to download. You can find the assembly instructions of this model with just go back and browse previous page.
Agree and download
Iron Man War Machine Poseable Paper Model Part 2 (Arm and Gatling Gun) - colored template - download
Iron Man War Machine Poseable Paper Model Part 2 (Arm and Gatling Gun) - blank template - download